Low-Volume CNC Machining – Milled and Turned Parts to Your Drawing
We manufacture small batches of metal parts from a quantity of one to your drawing: milled, turned, EDM-machined and ground, inspected on Zeiss coordinate measuring machines. Our focus is on parts that combine tight tolerances, difficult-to-machine materials or several manufacturing steps – exactly where a standard quote from an online configurator is no longer enough.
What we use to produce small batches
| Area | Equipment | Capacity | Key figure | For your small batch |
|---|---|---|---|---|
| 5-axis milling | 12 machining centres, 9 of them with simultaneous 5-axis machining | up to 2,100 × 1,800 × 1,250 mm, parts up to 8 t | Repeatability < 3 µm | complex parts in few setups |
| Turning | 2 turning centres, each with 12 driven tool stations | up to Ø 230 mm, spindle bore 67 mm | Turn-milling in one setup | Turned parts with cross holes, flats and threads |
| EDM | 3 wire EDM, 1 die-sinking EDM and 2 start-hole EDM machines | taper cuts up to ± 30° | surfaces down to Ra 0.1 µm | contours and hard materials beyond milling |
| Automation | 4 robot cells (EROWA, Indunorm) | 228 pallet positions | Setup parallel to machining | Setups are prepared while the machine is running |
| Metrology | Zeiss CONTURA G4, Zeiss DURA MAX, Keyence | parts up to 1,200 × 1,800 × 800 mm | Measurement uncertainty 2.0 + L/350 µm | First articles and follow-up lots traceably documented |
All figures are taken from our machine list, where you will find every machine with its travel ranges, control and equipment.
What we mean by a small batch
A small batch starts where a prototype has been approved and the same part is needed several times – as a pilot run, as a production ramp-up or as a recurring requirement in small lots. It is needed above all where dimensional accuracy matters more than the unit price: in mechanical and plant engineering, in medical technology, in semiconductor and vacuum technology.
We manufacture from a quantity of one. We do not state a fixed maximum quantity, because it depends on the part: on geometry, material, tolerance and how often it is reordered. For larger, regularly recurring quantities our automated series production is the right route, for first samples our prototype production.


Repeat orders
with the same parameters
Small batches rarely come only once. For a repeat order we work with the program, the clamping strategy and the inspection plan of the first order. The part is therefore produced not only to the same drawing but in the same way – and the inspection report remains comparable with the first lot.
How programs, fixtures and clamping devices are stored between two call-offs, and what this means for the price of the repeat order, is set out in our quotation.
How a small-batch enquiry works
You have one dedicated contact person from first contact to inspection report. Production stays entirely in house – part of our CNC machining services from a single source:
- Send drawing and key data: drawing with tolerances, a 3D model (STEP) if available, material, quantity and – if known – the expected call-off quantities.
- Check feasibility: we review geometry, tolerances and material and tell you what we can manufacture and where the limits are.
- Define the tolerance concept: before the first cut it is clear which dimension is inspected how and how it is documented.
- Manufacture in house: 5-axis milling, turning, EDM, grinding and surface finishing with no transport between processes.
- Inspect and deliver: measurement on Zeiss coordinate measuring machines, documentation according to the agreed concept, cleaned and securely packaged.
Materials
Bonsack specialises in difficult-to-machine alloys – titanium, Inconel, Hastelloy, Invar and Kovar. In addition there are stainless steel, aluminium and hardened tool steels, which we mill, EDM-machine and grind.
Which combination of material, tolerance and batch size is economical is clarified in our feasibility check – before a quotation is prepared.
Tolerances and proof
The repeatability of our Fehlmann machining centres is below 3 µm. Which tolerance your part achieves depends on geometry, material and clamping situation – which is why we agree it with you instead of promising a blanket figure.
It is proven in the measuring room: Zeiss CONTURA G4 with a measurement uncertainty of 2.0 + L/350 µm, Zeiss DURA MAX, an optical measuring projector from Keyence and around 500 fit and thread gauges.
We check your drawing and tell you what is feasible
Frequently asked questions about low-volume CNC machining
From what quantity do you produce small batches?
From a quantity of one. Single parts, prototypes and small lots are part of our everyday work. How economical a part is in very small quantities depends mainly on the programming and setup effort – we will tell you once we have seen the drawing.
Where does a small batch end and series production begin?
There is no fixed limit. What matters is whether a part runs regularly and in constant quantities. Then automated production on our robot cells with 228 pallet positions pays off – more on this under series production. With varying, smaller call-offs it remains a small batch.
When is a small batch economical?
With small quantities, programming, fixtures and setup are spread over few parts. They determine the unit price more than the actual machining time. A small batch becomes economical when the part is made in few setups, fixtures can be reused and repeat orders are foreseeable. For complex parts, 5-axis machining saves exactly these setups.
Can you reproduce parts later?
Yes. For a repeat order we work with the program, the clamping strategy and the inspection plan of the first order. How programs and fixtures are stored between call-offs and how this affects the price is set out in our quotation.
What documents do you need for a quotation?
A drawing with dimensions and tolerances, a 3D model (STEP) if available, the material, the quantity and details of surface finish and inspection scope. If you expect recurring call-offs, tell us the anticipated quantities – this changes the calculation.
Which materials and tolerances are possible?
We machine aluminium, stainless steel and tool steels as well as difficult-to-machine alloys such as titanium, Inconel, Hastelloy, Invar and Kovar. The achievable tolerance depends on geometry, material and clamping situation. Inspection and documentation are carried out on the Zeiss CONTURA G4 with a measurement uncertainty of 2.0 + L/350 µm.
Request a small batch
Send us your drawing or CAD model and state quantity and material.
We check feasibility, name the limits and get back to you promptly.